4 Replies Latest reply on Feb 17, 2016 11:05 AM by ctaz

    Galileo Board not completing the blink example

    ctaz

      Hi Guys ,

       

      I have been trying to run the blink example on the board and it kept getting stuck during upload for a while so i end up removing the board from the power supply . After following some solutions in the other threads which had a similar problem i did the following :

       

      1. Updated the firmware of the board to 1.0.4
      2. used the Arduino 1.6.0 IDE

       

      After trying to upload the blink example again I got the same problem. In both versions of Arduino IDE it gets stuck at this part :

       

       

      Sketch uses 57,967 bytes (0%) of program storage space. Maximum is 10,000,000 bytes.

      #!/bin/sh

      starting download script

       

      # clupload script to invoke lsz

      Args to shell: C:\arduino-1.6.0+Intel\hardware\tools\x86\bin C:\Users\CHIDO~1\AppData\Local\Temp\build1975236674310170855.tmp/Blink.cpp.elf COM3

      # Copyright (C) 2014 Intel Corporation

      COM PORT

      #

      Converted COM Port to tty port /dev/ttyS-1

      # This library is free software; you can redistribute it and/or

      Sending Command String to move to download if not already in download mode

      # modify it under the terms of the GNU Lesser General Public

      # License as published by the Free Software Foundation; either

      # version 2.1 of the License, or (at your option) any later version.

      #

      # This library is distributed in the hope that it will be useful,

      # but WITHOUT ANY WARRANTY; without even the implied warranty of

      # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU

      # Lesser General Public License for more details.

      #

      # You should have received a copy of the GNU Lesser General Public

      # License along with this library; if not, write to the Free Software

      # Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301  USA

      #

       

      echo "starting download script"

      echo "Args to shell:" $*

       

      Deleting existing sketch on target

      # ARG 1: Path to lsz executable.

      # ARG 2: Elf File to download

      # ARG 3: COM port to use.

       

      #path contains \ need to change all to /

      path_to_exe=$1

      fixed_path=${path_to_exe//\\/\/}

       

      #COM ports are not always setup to be addressed via COM for redirect.

      #/dev/ttySx are present. Howwever, COMy -> /dev/ttySx where x = y - 1

       

      com_port_arg=$3

      com_port_id=${com_port_arg/COM/}

      echo "COM PORT" $com_port_id

      tty_port_id=/dev/ttyS$((com_port_id-1))

      echo "Converted COM Port" $com_port_arg "to tty port" $tty_port_id

       

      echo "Sending Command String to move to download if not already in download mode"

      echo "~sketch downloadGalileo" > $tty_port_id

      C:\arduino-1.6.0+Intel/hardware/intel/i586-uclibc/tools/izmir/clupload_win.sh: line 42: /dev/ttyS-1: Read-only file system

       

      #Move the existing sketch on target.

      echo "Deleting existing sketch on target"

      "$fixed_path/lsz.exe" --escape -c "mv -f /sketch/sketch.elf /sketch/sketch.elf.old" <> $tty_port_id 1>&0

      C:\arduino-1.6.0+Intel/hardware/intel/i586-uclibc/tools/izmir/clupload_win.sh: line 46: /dev/ttyS-1: Read-only file system

      # Execute the target download command

       

      #Download the file.

      host_file_name=$2

      "$fixed_path/lsz.exe" --escape --binary --overwrite $host_file_name <> $tty_port_id 1>&0

      C:\arduino-1.6.0+Intel/hardware/intel/i586-uclibc/tools/izmir/clupload_win.sh: line 51: /dev/ttyS-1: Read-only file system

       

      #mv the downloaded file to /sketch/sketch.elf

      Moving downloaded file to /sketch/sketch.elf on target

      target_download_name="${host_file_name##*/}"

      echo "Moving downloaded file to /sketch/sketch.elf on target"

      "$fixed_path/lsz.exe" --escape -c "mv $target_download_name /sketch/sketch.elf; chmod +x /sketch/sketch.elf" <> $tty_port_id 1>&0

      C:\arduino-1.6.0+Intel/hardware/intel/i586-uclibc/tools/izmir/clupload_win.sh: line 56: /dev/ttyS-1: Read-only file system

       

       

       

      So how do i rectify this ? or is the board damaged ?

       

      thank you