2 Replies Latest reply on Mar 20, 2015 7:39 AM by jchozas

    [HELP] Edison, Do I need a new one??

    jchozas

      Hi all,

       

      I met a mistake trying to get free space in / and I have deleted all libraries from /usr/lib and obviously I have messed my Edison because I am stupid , Could I get solution for this or I have to buy a new one? ( I have the arduino breakout)

       

      I tried from Windows host run the recovery mode but the code got stucked and now I have lost the connectivity from the Edison's drive. I have tried to flash it from Linux host but it does not work.

       

      When I connect by serial console I got the following output:

       

      / #

      / #

      / #

      ******************************

      PSH KERNEL VERSION: b0182929

                      WR: 20104000

      ******************************

       

      SCU IPC: 0x800000d0  0xfffce92c

       

      PSH miaHOB version: TNG.B0.VVBD.0000000c

       

      microkernel built 10:14:01 Jan 13 2015

       

      ******* PSH loader *******

      PCM page cache size = 192 KB

      Cache Constraint = 0 Pages

      Arming IPC driver ..

      Adding page store pool ..

      PagestoreAddr(IMR Start Address) = 0x04899000

      pageStoreSize(IMR Size)          = 0x00080000

       

      *** Ready to receive application ***

       

       

      U-Boot 2014.04 (Jan 30 2015 - 14:15:53)

       

             Watchdog enabled

      DRAM:  980.6 MiB

      MMC:   tangier_sdhci: 0

      In:    serial

      Out:   serial

      Err:   serial

      Hit any key to stop autoboot:  0

      Target:blank

      Partitioning already done...

      Flashing already done...

      GADGET DRIVER: usb_dnl_dfu

      reading vmlinuz

      5348960 bytes read in 132 ms (38.6 MiB/s)

      Valid Boot Flag

      Setup Size = 0x00003c00

      Magic signature found

      Using boot protocol version 2.0c

      Linux kernel version 3.10.17-poky-edison+ (sys_dswci@tlsndgbuild004) #1 SMP PREEMPT Fri Jan 30 14:16:35 CET 2015

      Building boot_params at 0x00090000

      Loading bzImage at address 00100000 (5333600 bytes)

      Magic signature found

      Kernel command line: "root=PARTUUID=012b3303-34ac-284d-99b4-34e03a2335f4 rootfstype=ext4 console=ttyMFD2 earlyprintk=ttyMFD2,keep loglevel=4 systemd.unit=multi-user.target hardware_id=00 g_multi.iSerialNumber=1fe00dbe4a2de02648a91aba9cde839f"

       

      Starting kernel ...

       

      [    0.769306] pca953x 1-0020: failed reading register

      [    1.682362] pmic_ccsm pmic_ccsm: Error reading battery profile from battid frmwrk

      [    1.689754] pmic_ccsm pmic_ccsm: Battery Over heat exception

      [    1.689842] pmic_ccsm pmic_ccsm: Battery0 temperature inside boundary

      /bin/sh: can't access tty; job control turned off

      / #

      / # [   61.671528] snd_intel_sst: request fw failed

       

      And That is running over and over, although I can do "ls -l" command ,"df" command or "reboot ota" do not work either.

       

      ******************************

      PSH KERNEL VERSION: b0182929

                      WR: 20104000

      ******************************

       

      SCU IPC: 0x800000d0  0xfffce92c

       

      PSH miaHOB version: TNG.B0.VVBD.0000000c

       

      microkernel built 10:14:01 Jan 13 2015

       

      ******* PSH loader *******

      PCM page cache size = 192 KB

      Cache Constraint = 0 Pages

      Arming IPC driver ..

      Adding page store pool ..

      PagestoreAddr(IMR Start Address) = 0x04899000

      pageStoreSize(IMR Size)          = 0x00080000

       

      *** Ready to receive application ***

       

       

      U-Boot 2014.04 (Jan 30 2015 - 14:15:53)

       

             Watchdog enabled

      DRAM:  980.6 MiB

      MMC:   tangier_sdhci: 0

      In:    serial

      Out:   serial

      Err:   serial

      Hit any key to stop autoboot:  0

      Target:blank

      Partitioning already done...

      Flashing already done...

      GADGET DRIVER: usb_dnl_dfu

      reading vmlinuz

      5348960 bytes read in 132 ms (38.6 MiB/s)

      Valid Boot Flag

      Setup Size = 0x00003c00

      Magic signature found

      Using boot protocol version 2.0c

      Linux kernel version 3.10.17-poky-edison+ (sys_dswci@tlsndgbuild004) #1 SMP PREEMPT Fri Jan 30 14:16:35 CET 2015

      Building boot_params at 0x00090000

      Loading bzImage at address 00100000 (5333600 bytes)

      Magic signature found

      Kernel command line: "root=PARTUUID=012b3303-34ac-284d-99b4-34e03a2335f4 rootfstype=ext4 console=ttyMFD2 earlyprintk=ttyMFD2,keep loglevel=4 systemd.unit=multi-user.target hardware_id=00 g_multi.iSerialNumber=1fe00dbe4a2de02648a91aba9cde839f"

       

      Starting kernel ...

       

      [    0.759079] pca953x 1-0020: failed reading register

      [    1.666437] pmic_ccsm pmic_ccsm: Error reading battery profile from battid frmwrk

      [    1.677514] pmic_ccsm pmic_ccsm: Battery Over heat exception

      [    1.677600] pmic_ccsm pmic_ccsm: Battery0 temperature inside boundary

      /bin/sh: can't access tty; job control turned off

      / # [   61.656909] snd_intel_sst: request fw failed

       

       

       

      I have tried to flash Edison with Ubilinux but I got an error about a "xfstk tools". I have downloaded the package from from "http://xfstk.sourceforge.net/" but I get lost, Any help??

       

       

      [root@RHLE_5 toFlash]# sudo ./flashall.sh

      Using U-Boot target: edison-blankcdc

      Now waiting for dfu device 8087:0a99

      Please plug and reboot the board

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      ./flashall.sh: line 126: dfu-util: command not found

      Timed out while waiting for dfu device 8087:0a99

      DEBUG: lsusb

      ./flashall.sh: line 80: lsusb: command not found

      DEBUG: dfu-util -l

      ./flashall.sh: line 82: dfu-util: command not found

      Did you plug and reboot your board?

      If yes, please try a recovery by calling this script with the --recovery option

      [root@RHLE_5 toFlash]#

      [root@RHLE_5 toFlash]# sudo ./flashall.sh -v --recovery

      Starting Recovery mode

      Please plug and reboot the board

      Flashing IFWI

      which: no phoneflashtool in (/usr/bin:/bin)

      which: no xfstk-dldr-solo in (/usr/bin:/bin)

      !!! You should install xfstk tools, please visit http://xfstk.sourceforge.net/

      [root@RHLE_5 toFlash]#

       

      So, Do I need a new one or I would be able to get the Edison to live again?

       

      Thank you so much.