2 Replies Latest reply on Jun 16, 2014 1:10 PM by 4j1a

    Galileo - Windows 8 running Arduino Blink Sketch (error computing)

    4j1a

      Trying to Run an Arduino Sketch on the Galileo Intel Development Board.

      Windows 8 Arduino Sketch Blink

      Using Serial Port 3 assgined to Gadget Serial.

      Intel Galileo Card Selected.

      Firmware updated successfully.

       

      Followed the instruction from:

      Galileo_GettingStarted_329685_006.pdf from:

      Intel® Galileo Getting Started


      EsploraBlink | Arduino 1.5.3

      Error Compiling


      Arduino: 1.5.3 (Windows NT (unknown)), Board: "Intel® Galileo"

      C:\W4\G\arduino-1.5.3/hardware/tools/x86/i686-pokysdk-mingw32/usr/bin/i586-poky-linux-uclibc/i586-poky-linux-uclibc-g++ -m32 -march=i586 --sysroot=C:\W4\G\arduino-1.5.3/hardware/tools/x86/i586-poky-linux-uclibc -c -g -Os -w -fno-exceptions -ffunction-sections -fdata-sections -MMD -D__ARDUINO_X86__ -march=i586 -m32 -DARDUINO=153 -IC:\W4\G\arduino-1.5.3\hardware\arduino\x86\cores\arduino -IC:\W4\G\arduino-1.5.3\hardware\arduino\x86\variants\galileo_fab_d C:\Users\Y\AppData\Local\Temp\build2476004411176264358.tmp\EsploraBlink.cpp -o C:\Users\Y\AppData\Local\Temp\build2476004411176264358.tmp\EsploraBlink.cpp.o

      EsploraBlink.ino:17:21: fatal error: Esplora.h: No such file or directory
      compilation terminated.


      Every thing was fine until Arduino reached the following line, where the font turned into a halloween -orange:


      EsploraBlink.ino:17:21: fatal error: Esplora.h: No such file or directory

      compilation terminated.

       

      File EsploraBlink.ino located at c:\w4\g\sketches\EsploraBlink.ino

       

      Sketch:

      /*
        Esplora Blink

      This  sketch blinks the Esplora's RGB LED. It goes through
      all three primary colors (red, green, blue), then it
      combines them for secondary colors(yellow, cyan, magenta), then
      it turns on all the colors for white.
      For best results cover the LED with a piece of white paper to see the colors.

      Created on 22 Dec 2012
      by Tom Igoe

      This example is in the public domain.
      */

      #include <Esplora.h>


      void setup() {
        // There's nothing to set up for this sketch
      }

      void loop() {
        Esplora.writeRGB(255,0,0);    // make the LED red
        delay(1000);                  // wait 1 second
        Esplora.writeRGB(0,255,0);    // make the LED green
        delay(1000);                  // wait 1 second
        Esplora.writeRGB(0,0,255);    // make the LED blue
        delay(1000);                  // wait 1 second
        Esplora.writeRGB(255,255,0);  // make the LED yellow
        delay(1000);                  // wait 1 second
        Esplora.writeRGB(0,255,255);  // make the LED cyan
        delay(1000);                  // wait 1 second
        Esplora.writeRGB(255,0,255);  // make the LED magenta
        delay(1000);                  // wait 1 second
        Esplora.writeRGB(255,255,255);// make the LED white
        delay(1000);