3 Replies Latest reply on May 21, 2009 1:31 PM by Aryan2411

    d102ggc2 motherboard doesn't boot from ide hard disk

    chaitanya84

      Hello friends,

       

      In last month I upgrade the pc with intel p4 3.0 prc and intel d102ggc2 motherboard, and try to install windows XP on it.

      While installtion first time it boot boot from cd-rom properly but next time (once the prerquest installtion complete and first time aftre restart) it does not boot from hard disk.

      But in BIOS it show the hdd properly as well as in drive selection for installing os it show disk drives correctly.

      I use the my old ide hdd. Please give me sugession to slove these problem.

       

      Thanks in advance.

        • 1. Re: d102ggc2 motherboard doesn't boot from ide hard disk
          Aryan2411

          Hi there,

           

          Have you tried this:

          Go into the BIOS

          Go to Boot Menu
          Boot Menu: Advance
          Boot Priority: Hard Disk Drive First
          Boot to Removable Devices Disable
          Boot to Network Disable
          Boot to Optical Device Disable
          USB Boot Disable
          Boot USB Device First Disable
          USB Mass Storage Auto

           

          Make sure to set the drives which has the OS installed on the 1st boot priority.

           

          Let me know how it goes.

           

          Regards,

          Aryan

          • 2. Re: d102ggc2 motherboard doesn't boot from ide hard disk
            chaitanya84

            Thanks for the ur suggestion .

            i tried it but its not working.

             

            Is there is any alternative way. Please suggest.

            If I need to update the BIOS please help me

            • 3. Re: d102ggc2 motherboard doesn't boot from ide hard disk
              Aryan2411

              Hi there,

               

              I will explain to you how to make a BIOS update through the BIOS Recovery Mode:

               

              Instructions for Recovery BIOS Updates
              In the unlikely event that a BIOS update is interrupted, it is possible the BIOS may be left in an unusable state. The recovery process requires the chassis to be opened to move the onboard BIOS Configuration Jumper.

              1. Copy the recovery file (*.bio) to a formatted usb disk.

              File: http://downloadcenter.intel.com/T8Clearance.aspx?sType=&agr=Y&ProductID=2367&DwnldID=12686&url=/12686/eng/GC1087.BIO&PrdMap=&strOSs=38&OSFullName=OSIndependent&lang=eng


              2. Place the usb disk in the target system.


              3. Shut down the system and unplug AC power.


              4. Open the chassis and remove the BIOS Configuration Jumper. See the Technical Product Specification for details including the location of this jumper.
              5. Power the system on.


              6. Wait 2-5 minutes for the update to complete. When the usb drive LED is lit, the system is copying the recovery code into the FLASH device.

              7. System will either turn off when the recovery process is completed or it will prompt you to turn off the system.


              8. Remove usb disk


              9. Replace the BIOS Configuration Jumper.


              10. Restart system.

               

              Note: Dont connect any other usb devices, media drive to the system other than just the recvoery media. If you can't do it via the USB, use a blank CD. Then connect only the CD Drive.

               

              Note: these can be found on:
              Website: http://downloadmirror.intel.com/17197/eng/BIOS%20Update%20Readme.pdf
              Page 3

               

              There are other methods as well, Iflash Method, ISO Method where jumper is not required to be removed. etc.

               

              Brief on IFlash:

              - Media drive needs to be bootable like bootable USB or CD

              - Files needed Iflash.exe, .BIO file

              - Command: iflash /pf xxx.bio

               

              Brief on ISO:

              - Burn the ISO file on a blank CD using software like PowerIso.

              - Boot the system on to the CD.

              - Run the batch file

               

              Hope this helps a bit.

               

              Regards,

              Aryan.