2 Replies Latest reply on Nov 6, 2011 6:24 AM by mc.sim

    NIC Intel PRO/1000MT with PCI-X red indication

    mc.sim

      hi all

       

      There is a dual-port NIC Intel PRO/1000MT with  PCI-X bus (on a normal PCI appear similar problems).
      Network Adapter installed in a motherboard Intel SE7500CW2 in PCI-X 133 Mhz
      Installed Debian 6.0.2
      Both interfaces are configured as a network card bonding:
      ==========================================================
      files ~ # cat /etc/network/interfaces
      # The loopback network interface
      auto lo
      iface lo inet loopback
      # The primary network interface
      auto bond0 eth2 eth3
      iface bond0 inet static
              address 10.0.0.11
              netmask 255.255.255.0
              gateway 10.0.0.254
              bond-slaves none
              bond-mode balance-alb
              bond-downdelay 200
              bond-updelay 200
      allow-hotplug eth2
      iface eth2 inet manual
              bond-master bond0
              bond-primary eth2 eth3
      allow-hotplug eth3
      iface eth3 inet manual
              bond-master bond0
              bond-primary eth2 eth3
      files ~ # cat /etc/modprobe.d/aliases-bond.conf
      alias bond0 bonding
              options bonding arp_interval=200 arp_ip_target=10.0.0.1,10.0.0.4
      files ~ # ifconfig
      bond0     Link encap:Ethernet  HWaddr 00:07:e9:a5:14:f7
                inet addr:10.0.0.11  Bcast:10.0.0.255  Mask:255.255.255.0
                UP BROADCAST RUNNING MASTER MULTICAST  MTU:1500  Metric:1
                RX packets:44564 errors:0 dropped:0 overruns:0 frame:0
                TX packets:47089 errors:0 dropped:0 overruns:0 carrier:0
                collisions:0 txqueuelen:0
                RX bytes:8311464 (7.9 MiB)  TX bytes:39156386 (37.3 MiB)
      eth2      Link encap:Ethernet  HWaddr 00:07:e9:a5:14:f7
                UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1
                RX packets:31352 errors:0 dropped:0 overruns:0 frame:0
                TX packets:37836 errors:0 dropped:0 overruns:0 carrier:0
                collisions:0 txqueuelen:1000
                RX bytes:5245222 (5.0 MiB)  TX bytes:38583024 (36.7 MiB)
      eth3      Link encap:Ethernet  HWaddr 00:07:e9:a5:14:f6
                UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1
                RX packets:13212 errors:0 dropped:0 overruns:0 frame:0
                TX packets:9253 errors:0 dropped:0 overruns:0 carrier:0
                collisions:0 txqueuelen:1000
                RX bytes:3066242 (2.9 MiB)  TX bytes:573362 (559.9 KiB)
      lo        Link encap:Local Loopback
                inet addr:127.0.0.1  Mask:255.0.0.0
                UP LOOPBACK RUNNING  MTU:16436  Metric:1
                RX packets:31 errors:0 dropped:0 overruns:0 frame:0
                TX packets:31 errors:0 dropped:0 overruns:0 carrier:0
                collisions:0 txqueuelen:0
                RX bytes:2568 (2.5 KiB)  TX bytes:2568 (2.5 KiB)
      ===============================================================
      When I disconnect the wire from one of the interfaces to the console messages are displayed:
      In the log file / var / log / messages a lot of these messages:
      =================================================================
      Aug  5 18:40:25 files kernel: [    9.912383] e1000: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
      Aug  5 18:40:25 files kernel: [    9.925118] bonding: bond0: Warning: failed to get speed and duplex from eth3, assumed to be 100Mb/sec and Full.
      Aug  5 18:40:25 files kernel: [    9.925149] bonding: bond0: enslaving eth3 as an active interface with an up link.
      Aug  5 18:40:25 files kernel: [    9.925164] bonding: bond0: Setting eth2 as primary slave.
      Aug  5 18:40:25 files kernel: [    9.930836] bonding: bond0: Setting eth2 as primary slave.
      Aug  5 18:40:25 files kernel: [    9.944397] e1000: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
      Aug  5 18:40:25 files kernel: [   11.180611] lp0: using parport0 (interrupt-driven).
      Aug  5 18:40:25 files kernel: [   11.197377] ppdev: user-space parallel port driver
      Aug  5 18:42:57 files kernel: [  162.492113] e1000: eth2 NIC Link is Down
      Aug  5 18:43:01 files kernel: [  167.300017] bonding: bond0: interface eth2 is now down.
      Aug  5 18:43:01 files kernel: [  167.300030] bonding: bond0: making interface eth3 the new active one.
      Aug  5 18:43:01 files kernel: [  167.300253] Pid: 848, comm: bond0 Not tainted 2.6.32-5-686 #1
      Aug  5 18:43:01 files kernel: [  167.300258] Call Trace:
      Aug  5 18:43:01 files kernel: [  167.300276]  [<f8234266>] ? bond_alb_handle_active_change+0xec/0x158 [bonding]
      Aug  5 18:43:01 files kernel: [  167.300286]  [<f822f23e>] ? bond_change_active_slave+0x1dc/0x42b [bonding]
      Aug  5 18:43:01 files kernel: [  167.300299]  [<c126d49e>] ? schedule+0x78f/0x7dc
      Aug  5 18:43:01 files kernel: [  167.300308]  [<f822f7a8>] ? bond_select_active_slave+0x86/0xb4 [bonding]
      Aug  5 18:43:01 files kernel: [  167.300317]  [<f822fe10>] ? bond_loadbalance_arp_mon+0x186/0x1b8 [bonding]
      Aug  5 18:43:01 files kernel: [  167.300327]  [<c10412f7>] ? worker_thread+0x141/0x1bd
      Aug  5 18:43:01 files kernel: [  167.300336]  [<f822fc8a>] ? bond_loadbalance_arp_mon+0x0/0x1b8 [bonding]
      Aug  5 18:43:01 files kernel: [  167.300345]  [<c104403a>] ? autoremove_wake_function+0x0/0x2d
      Aug  5 18:43:01 files kernel: [  167.300351]  [<c10411b6>] ? worker_thread+0x0/0x1bd
      Aug  5 18:43:01 files kernel: [  167.300358]  [<c1043e08>] ? kthread+0x61/0x66
      Aug  5 18:43:01 files kernel: [  167.300365]  [<c1043da7>] ? kthread+0x0/0x66
      Aug  5 18:43:01 files kernel: [  167.300374]  [<c1003d47>] ? kernel_thread_helper+0x7/0x10
      Aug  5 18:43:01 files kernel: [  167.300475] Pid: 848, comm: bond0 Not tainted 2.6.32-5-686 #1
      Aug  5 18:43:01 files kernel: [  167.300932] Call Trace:
      Aug  5 18:43:01 files kernel: [  167.300941]  [<c121836f>] ? inetdev_event+0x40/0x3c3
      Aug  5 18:43:01 files kernel: [  167.300950]  [<c11f39e6>] ? rt_cache_flush+0x13f/0x161
      Aug  5 18:43:01 files kernel: [  167.300957]  [<c12702c8>] ? notifier_call_chain+0x2a/0x47
      Aug  5 18:43:01 files kernel: [  167.300964]  [<c10476ce>] ? raw_notifier_call_chain+0x9/0xc
      Aug  5 18:43:01 files kernel: [  167.300971]  [<c11da5ea>] ? dev_set_mac_address+0x4d/0x52
      Aug  5 18:43:01 files kernel: [  167.300981]  [<f8233933>] ? alb_set_slave_mac_addr+0x68/0xa2 [bonding]
      Aug  5 18:43:01 files kernel: [  167.300991]  [<f82339a7>] ? alb_swap_mac_addr+0x3a/0x4f [bonding]
      Aug  5 18:43:01 files kernel: [  167.301000]  [<f823427c>] ? bond_alb_handle_active_change+0x102/0x158 [bonding]
      Aug  5 18:43:01 files kernel: [  167.301009]  [<f822f23e>] ? bond_change_active_slave+0x1dc/0x42b [bonding]
      Aug  5 18:43:01 files kernel: [  167.301017]  [<c126d49e>] ? schedule+0x78f/0x7dc
      Aug  5 18:43:01 files kernel: [  167.301025]  [<f822f7a8>] ? bond_select_active_slave+0x86/0xb4 [bonding]
      Aug  5 18:43:01 files kernel: [  167.301034]  [<f822fe10>] ? bond_loadbalance_arp_mon+0x186/0x1b8 [bonding]
      Aug  5 18:43:01 files kernel: [  167.301041]  [<c10412f7>] ? worker_thread+0x141/0x1bd
      Aug  5 18:43:01 files kernel: [  167.301049]  [<f822fc8a>] ? bond_loadbalance_arp_mon+0x0/0x1b8 [bonding]
      Aug  5 18:43:01 files kernel: [  167.301056]  [<c104403a>] ? autoremove_wake_function+0x0/0x2d
      Aug  5 18:43:01 files kernel: [  167.301062]  [<c10411b6>] ? worker_thread+0x0/0x1bd
      Aug  5 18:43:01 files kernel: [  167.301068]  [<c1043e08>] ? kthread+0x61/0x66
      Aug  5 18:43:01 files kernel: [  167.301074]  [<c1043da7>] ? kthread+0x0/0x66
      Aug  5 18:43:01 files kernel: [  167.301081]  [<c1003d47>] ? kernel_thread_helper+0x7/0x10
      .......
      Aug  5 18:43:01 files kernel: [  167.302048] Pid: 848, comm: bond0 Not tainted 2.6.32-5-686 #1
      Aug  5 18:43:01 files kernel: [  167.302052] Call Trace:
      Aug  5 18:43:01 files kernel: [  167.302059]  [<c11d8778>] ? __dev_set_promiscuity+0x2f/0x128
      Aug  5 18:43:01 files kernel: [  167.302066]  [<c11d8c47>] ? dev_set_promiscuity+0x10/0x2e
      Aug  5 18:43:01 files kernel: [  167.302075]  [<f8233dcd>] ? rlb_teach_disabled_mac_on_primary+0x22/0x44 [bonding]
      Aug  5 18:43:01 files kernel: [  167.302084]  [<f8234288>] ? bond_alb_handle_active_change+0x10e/0x158 [bonding]
      Aug  5 18:43:01 files kernel: [  167.302093]  [<f822f23e>] ? bond_change_active_slave+0x1dc/0x42b [bonding]
      Aug  5 18:43:01 files kernel: [  167.302101]  [<c126d49e>] ? schedule+0x78f/0x7dc
      Aug  5 18:43:01 files kernel: [  167.302109]  [<f822f7a8>] ? bond_select_active_slave+0x86/0xb4 [bonding]
      Aug  5 18:43:01 files kernel: [  167.302118]  [<f822fe10>] ? bond_loadbalance_arp_mon+0x186/0x1b8 [bonding]
      Aug  5 18:43:01 files kernel: [  167.302125]  [<c10412f7>] ? worker_thread+0x141/0x1bd
      Aug  5 18:43:01 files kernel: [  167.302134]  [<f822fc8a>] ? bond_loadbalance_arp_mon+0x0/0x1b8 [bonding]
      Aug  5 18:43:01 files kernel: [  167.302141]  [<c104403a>] ? autoremove_wake_function+0x0/0x2d
      Aug  5 18:43:01 files kernel: [  167.302147]  [<c10411b6>] ? worker_thread+0x0/0x1bd
      Aug  5 18:43:01 files kernel: [  167.302153]  [<c1043e08>] ? kthread+0x61/0x66
      Aug  5 18:43:01 files kernel: [  167.302159]  [<c1043da7>] ? kthread+0x0/0x66
      Aug  5 18:43:01 files kernel: [  167.302165]  [<c1003d47>] ? kernel_thread_helper+0x7/0x10
      Aug  5 18:43:01 files kernel: [  167.302170] device eth3 entered promiscuous mode
      Aug  5 18:43:02 files kernel: [  168.024374] e1000: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
      Aug  5 18:43:11 files kernel: [  177.296030] device eth3 left promiscuous mode
      Aug  5 18:43:33 files kernel: [  199.300018] bonding: bond0: interface eth2 is now up
      Aug  5 18:43:45 files kernel: [  211.140114] e1000: eth2 NIC Link is Down
      Aug  5 18:43:49 files kernel: [  215.300017] bonding: bond0: interface eth2 is now down.
      Aug  5 18:43:51 files kernel: [  217.332372] e1000: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
      Aug  5 18:44:00 files kernel: [  226.364113] e1000: eth3 NIC Link is Down
      Aug  5 18:44:05 files kernel: [  231.300021] bonding: bond0: interface eth3 is now down.
      Aug  5 18:44:05 files kernel: [  231.300088] bonding: bond0: now running without any active interface !
      Aug  5 18:44:07 files kernel: [  232.980372] e1000: eth3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX
      Aug  5 18:44:23 files kernel: [  249.300014] bonding: bond0: link status definitely up for interface eth2,
      Aug  5 18:44:23 files kernel: [  249.300034] bonding: bond0: making interface eth2 the new active one.
      Aug  5 18:44:23 files kernel: [  249.300225] Pid: 848, comm: bond0 Not tainted 2.6.32-5-686 #1
      Aug  5 18:44:23 files kernel: [  249.300230] Call Trace:
      Aug  5 18:44:23 files kernel: [  249.300248]  [<f8234266>] ? bond_alb_handle_active_change+0xec/0x158 [bonding]
      Aug  5 18:44:23 files kernel: [  249.300258]  [<f822f23e>] ? bond_change_active_slave+0x1dc/0x42b [bonding]
      Aug  5 18:44:23 files kernel: [  249.300270]  [<c126d49e>] ? schedule+0x78f/0x7dc
      Aug  5 18:44:23 files kernel: [  249.300279]  [<f822f7a8>] ? bond_select_active_slave+0x86/0xb4 [bonding]
      Aug  5 18:44:23 files kernel: [  249.300288]  [<f822fe10>] ? bond_loadbalance_arp_mon+0x186/0x1b8 [bonding]
      Aug  5 18:44:23 files kernel: [  249.300299]  [<c10412f7>] ? worker_thread+0x141/0x1bd
      Aug  5 18:44:23 files kernel: [  249.300307]  [<f822fc8a>] ? bond_loadbalance_arp_mon+0x0/0x1b8 [bonding]
      Aug  5 18:44:23 files kernel: [  249.300316]  [<c104403a>] ? autoremove_wake_function+0x0/0x2d
      //////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
      -- System Information:
      Architecture: i386 (i686)
      Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core)
      Versions of packages ifenslave-2.6 depends on:
      ii  iproute                       20100519-3 networking and traffic control too
      ii  libc6                         2.11.2-10  Embedded GNU C Library: Shared lib
      Versions of packages ifenslave-2.6 recommends:
      ii  net-tools                     1.60-23    The NET-3 networking toolkit
      ifenslave-2.6 suggests no packages.
      ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
      Port having the issue showing a red indication. About this documentation does not say:
      hope for your help!
      thanks