0 Replies Latest reply on Aug 28, 2017 4:19 AM by Ramesh51

    Intel edison bootup problem

    Ramesh51

      Hi!

       

       

       

      I am facing problem while working with Intel Edison.

       

      It was booted up well till yesterday but after upgrading it is not booting up properly.

       

       

       

      Please help me for the following error

       

       

       

       

       

      U-Boot 2014.04 (Apr 29 2015 - 04:05:44)

       

             Watchdog enabled

      DRAM:  980.6 MiB

      MMC:   tangier_sdhci: 0

      In:    serial

      Out:   serial

      Err:   serial

      Hit any key to stop autoboot:  0

      Target:blank

      Partitioning already done...

      Flashing already done...

      GADGET DRIVER: usb_dnl_dfu

      reading vmlinuz

      5338304 bytes read in 133 ms (38.3 MiB/s)

      Valid Boot Flag

      Setup Size = 0x00003c00

      Magic signature found

      Using boot protocol version 2.0c

      Linux kernel version 3.10.17-yocto-standard (sys_dswci@tlsndgbuild004) #1 SMP PREEMPT Wed Apr 29 04:08:25 CEST 2015

      Building boot_params at 0x00090000

      Loading bzImage at address 00100000 (5322944 bytes)

      Magic signature found

      Kernel command line: "rootwait root=PARTUUID=012b3303-34ac-284d-99b4-34e03a2335f4 rootfstype=ext4 console=ttyMFD2 earlyprintk=ttyMFD2,keep loglevel=4 g_multi.ethernet_config=rndis systemd.unit=multi-user.target hardware_id=00 g_multi.iSerialNumber=d16235eb2845afb010c08be983de6ae3 g_multi.dev_addr=02:00:86:de:6a:e3 platform_mrfld_audio.audio_codec=dummy"

       

      Starting kernel ...

       

      [    1.653757] snd_soc_sst_platform: Enter:sst_soc_probe

      [    2.007537] pmic_ccsm pmic_ccsm: Error reading battery profile from battid frmwrk

      [    2.015949] pmic_ccsm pmic_ccsm: Battery Over heat exception

       

      Welcome to Linux!

       

               Expecting device dev-ttyMFD2.device...

      [  OK  ] Reached target Remote File Systems.

               Expecting device sys-subsystem-net-devices-wlan0.device...

               Expecting device dev-disk-by\x2dpartlabel-factory.device...

               Expecting device sys-subsystem-net-devices-usb0.device...

      [  OK  ] Reached target Paths.

      [  OK  ] Set up automount Arbitrary Executable File Formats F...utomount Point.

      [  OK  ] Reached target Swap.

      [  OK  ] Set up automount boot.automount.

      [  OK  ] Created slice Root Slice.

      [  OK  ] Listening on Journal Socket.

      [  OK  ] Listening on Delayed Shutdown Socket.

      [  OK  ] Listening on udev Kernel Socket.

      [  OK  ] Listening on udev Control Socket.

      [  OK  ] Listening on /dev/initctl Compatibility Named Pipe.

      [  OK  ] Created slice User and Session Slice.

      [  OK  ] Created slice System Slice.

               Mounting POSIX Message Queue File System...

               Mounting Debug File System...

               Starting Journal Service...

      [  OK  ] Started Journal Service.

               Starting Create list of required static device nodes...rrent kernel...

               Starting Apply Kernel Variables...

               Starting udev Coldplug all Devices...

               Starting Load Kernel Modules...

      [  OK  ] Reached target Slices.

               Starting Remount Root and Kernel File Systems...

      [  OK  ] Created slice system-serial\x2dgetty.slice.

      [  OK  ] Created slice system-getty.slice.

               Mounting Temporary Directory...

      [  OK  ] Set up automount home.automount.

      [  OK  ] Mounted Debug File System.

      [  OK  ] Mounted POSIX Message Queue File System.

      [  OK  ] Mounted Temporary Directory.

      [  OK  ] Started Create list of required static device nodes ...current kernel.

      [  OK  ] Started Apply Kernel Variables.

      [  OK  ] Started Remount Root and Kernel File Systems.

      [  OK  ] Started udev Coldplug all Devices.

      [  OK  ] Started Load Kernel Modules.

               Mounting FUSE Control File System...

               Mounting Configuration File System...

               Starting Load/Save Random Seed...

               Starting Create Static Device Nodes in /dev...

      [  OK  ] Mounted Configuration File System.

      [  OK  ] Mounted FUSE Control File System.

      [  OK  ] Started Load/Save Random Seed.

      [  OK  ] Started Create Static Device Nodes in /dev.

               Starting udev Kernel Device Manager...

      [  OK  ] Reached target Local File Systems (Pre).

               Mounting /var/volatile...

      [  OK  ] Mounted /var/volatile.

      [  OK  ] Started udev Kernel Device Manager.

      [  OK  ] Reached target Local File Systems.

               Starting Trigger Flushing of Journal to Persistent Storage...

               Starting Create Volatile Files and Directories...

      [  OK  ] Set up automount Automount for SDCard.

      [  OK  ] Started Trigger Flushing of Journal to Persistent Storage.

      [  OK  ] Started Create Volatile Files and Directories.

               Starting Network Time Synchronization...

               Starting Update UTMP about System Boot/Shutdown...

      [  OK  ] Started Network Time Synchronization.

      [  OK  ] Found device /dev/ttyMFD2.

      [  OK  ] Started Update UTMP about System Boot/Shutdown.

      [  OK  ] Found device /dev/disk/by-partlabel/factory.

      [  OK  ] Unset automount Automount for SDCard.

               Mounting Mount for SDCard...

               Mounting Mount for factory...

      [  OK  ] Reached target System Initialization.

      [  OK  ] Reached target Timers.

      [  OK  ] Listening on D-Bus System Message Bus Socket.

               Starting Console System Startup Logging...

               Starting Restore Sound Card State...

      [  OK  ] Mounted Mount for SDCard.

      [  OK  ] Mounted Mount for factory.

      [FAILED] Failed to start Console System Startup Logging.

      See 'systemctl status console-kit-log-system-start.service' for details.

      [  OK  ] Found device /sys/subsystem/net/devices/wlan0.

      [  OK  ] Found device /sys/subsystem/net/devices/usb0.

      [  OK  ] Created slice system-systemd\x2dfsck.slice.

               Starting File System Check on /dev/disk/by-partlabel/home...

      [  OK  ] Created slice system-systemd\x2drfkill.slice.

               Starting Load/Save RF Kill Switch Status of rfkill2...

               Starting Load/Save RF Kill Switch Status of rfkill1...

               Starting Load/Save RF Kill Switch Status of rfkill0...

      [  OK  ] Reached target Sound Card.

      [  OK  ] Listening on sshd.socket.

      [  OK  ] Started Load/Save RF Kill Switch Status of rfkill2.

      [  OK  ] Started Load/Save RF Kill Switch Status of rfkill1.

      [  OK  ] Started Load/Save RF Kill Switch Status of rfkill0.

      [    8.115608] systemd-fsck[180]: /dev/mmcblk0p10: recovering journal

      [    8.151136] systemd-fsck[180]: /dev/mmcblk0p10: clean, 14/87120 files, 14183/348155 blocks

      [  OK  ] Started File System Check on /dev/disk/by-partlabel/home.

               Mounting /home...

      [  OK  ] Reached target Sockets.

      [  OK  ] Reached target Basic System.

               Starting Edison PWR button handler...

      [  OK  ] Started Edison PWR button handler.

               Starting Start or stop WiFI AP Mode in Edison...

      [  OK  ] Started Start or stop WiFI AP Mode in Edison.

               Starting Bluetooth rf kill event daemon...

      [  OK  ] Started Bluetooth rf kill event daemon.

               Starting WPA supplicant service...

               Starting Daemon to handle arduino sketches...

      [  OK  ] Started Daemon to handle arduino sketches.

               Starting Daemon to load edison mcu app binary...

      [  OK  ] Started Daemon to load edison mcu app binary.

      Application available at (physical) address 0x04819000

              VRL mapped to 0xff217000

              App size = 11508 bytes

       

              App Authentication feature is disabled!

              Resetting IPC

       

      *** Ready to receive applicat▒s▒▒▒E▒▒ѥ▒▒▒z▒▒▒▒▒L▒         Starting Daemon to reset sketches...

      [  OK  ] Started Daemon to reset sketches.

               Starting Permit User Sessions...

               Starting D-Bus System Message Bus...

      [  OK  ] Started D-Bus System Message Bus.

               Starting Network Service...

               Starting Login Service...

               Starting Crashlog service...

      [  OK  ] Started Crashlog service.

               Starting Cleanjournal service...

      [  OK  ] Started Cleanjournal service.

               Starting Watchdog sample daemon...

      [  OK  ] Started Watchdog sample daemon.

      [  OK  ] Mounted /home.

      [  OK  ] Started Network Service.

      [  OK  ] Started OpenSSH Key Generation.

      [  OK  ] Started Permit User Sessions.

      [  OK  ] Started Login Service.

      [  OK  ] Started Restore Sound Card State.

               Starting PulseAudio Sound System...

               Starting Daemon to receive the wpa_supplicant event...

      [  OK  ] Started Daemon to receive the wpa_supplicant event.

               Starting Serial Getty on ttyMFD2...

      [  OK  ] Started Serial Getty on ttyMFD2.

               Starting Getty on tty1...

      [  OK  ] Started Getty on tty1.

      [  OK  ] Reached target Login Prompts.

               Starting Network Name Resolution...

      [  OK  ] Reached target Network.

               Starting Mosquitto - lightweight server implementati...SN protocols...

               Starting Zero-configuration networking...

      [  OK  ] Started Network Name Resolution.

      [FAILED] Failed to start PulseAudio Sound System.

      See 'systemctl status pulseaudio.service' for details.

      [  OK  ] Started Mosquitto - lightweight server implementatio...T-SN protocols.

               Starting Daemon to receive the wpa_supplicant event...

      [  OK  ] Started Daemon to receive the wpa_supplicant event.

               Starting Bluetooth service...

               Stopping PulseAudio Sound System...

      [  OK  ] Stopped PulseAudio Sound System.

               Starting PulseAudio Sound System...

      [  OK  ] Started WPA supplicant service.

      [  OK  ] Started Zero-configuration networking.

      [  OK  ] Started Bluetooth service.

      [FAILED] Failed to start PulseAudio Sound System.

      See 'systemctl status pulseaudio.service' for details.

               Stopping PulseAudio Sound System...

      [  OK  ] Stopped PulseAudio Sound System.

               Starting PulseAudio Sound System...

               Stopping Daemon to receive the wpa_supplicant event...

      [  OK  ] Stopped Daemon to receive the wpa_supplicant event.

               Starting Daemon to receive the wpa_supplicant event...

      [  OK  ] Started Daemon to receive the wpa_supplicant event.

               Starting Hostname Service...

               Starting The Edison status and configuration service...

      [  OK  ] Started The Edison status and configuration service.

               Starting Intel_XDK_Daemon...

      [  OK  ] Started Intel_XDK_Daemon.

      [FAILED] Failed to start PulseAudio Sound System.

      See 'systemctl status pulseaudio.service' for details.

      [  OK  ] Started Hostname Service.

      [  OK  ] Reached target Multi-User System.

       

      Poky (Yocto Project Reference Distro) 1.7.3 edison ttyMFD2

       

      edison login:

       

       

       

       

      I just wanted to reset it to factory version

      I tried with boot> run do_ota

       

      but still I'm unable to resolve it!

      What should I have to do now....please suggest me!

       

       

       

       

       

      Thank You.