1 Reply Latest reply on Apr 12, 2017 3:36 AM by transcendi

    quark c1000 - Update ROM error from ISSM

    transcendi

      Hi.

       

      I am trying to use Intel® QuarkTM SE Microcontroller C1000 Development Platform.

      So I followed Get Started link below.

      Get Started with the Intel® Quark™ SE microcontroller C1000 | IoT | Intel® Software

      But i failed in step 3. c. follow the gaetting started of ISSM welcome page.

       

      I got error massage when Update Microcontroller ROM

       

      Could not update the ROM. Flash ROM failed.

      Open On-Chip Debugger 0.8.0-dev-gba72ade-dirty (2016-07-19-11:13)

      Licensed under GNU GPL v2

      For bug reports, read

        http://openocd.sourceforge.net/doc/doxygen/bugs.html

      Info : only one transport option; autoselect 'jtag'

      adapter speed: 1000 kHz

      trst_only separate trst_push_pull

      jtag_ntrst_delay: 300

      Info : clock speed 1000 kHz

      Info : JTAG tap: quark_se.cltap tap/device found: 0x0e765013 (mfg: 0x009, part: 0xe765, ver: 0x0)

      Enabling arc core tap

      Info : JTAG tap: quark_se.arc-em enabled

      Enabling quark core tap

      Info : JTAG tap: quark_se.quark enabled

      Processor type: arc-em

      redirect to PM, tapstatus=0x00300c14

      unknown break reason at 0x0000fff0

      Setup clock

      adapter speed: 4 kHz

      adapter speed: 1000 kHz

      Info : JTAG tap: quark_se.cltap tap/device found: 0x0e765013 (mfg: 0x009, part: 0xe765, ver: 0x0)

      Enabling arc core tap

      Info : JTAG tap: quark_se.arc-em enabled

      Enabling quark core tap

      Info : JTAG tap: quark_se.quark enabled

      target state: halted

      target halted due to debug-request at 0x0000fff0 in real mode

      target state: halted

      Info : JTAG tap: quark_se.cltap tap/device found: 0x0e765013 (mfg: 0x009, part: 0xe765, ver: 0x0)

      Enabling arc core tap

      Info : JTAG tap: quark_se.arc-em enabled

      Enabling quark core tap

      Info : JTAG tap: quark_se.quark enabled

      target running for unknown reason

      Info : JTAG tap: quark_se.cltap tap/device found: 0x0e765013 (mfg: 0x009, part: 0xe765, ver: 0x0)

      Enabling arc core tap

      Info : JTAG tap: quark_se.arc-em enabled

      Enabling quark core tap

      Info : JTAG tap: quark_se.quark enabled

      target state: halted

      target halted due to debug-request at 0xffffe29d in protected mode

      target state: halted

      target halted due to debug-request at 0x0000fff0 in real mode

      target state: halted

      Start flash

      .

       

      My development environment is Windows 7

      Connect usb on FTD_USB only

      Can find OpenOCD JTAG from Windows Device manager

      Try grounding J14 Pin 28 on the board but fail

      And I did run the LED blink example with a previous version of ISSM few months ago

       

      If I ignore the above error, build and run the LED blink example, there is no error and i can see 1.26KiB Flash1 used, 80B SRAM used but no led blinking.

      And on hello world example, i can only "?" on Serial Terminal of ISSM.

       

      How can i fix the problem?

       

      Thanks,

      Jeong

       

      Jeong Hasang 님이 메시지를 편집했습니다.