1 Reply Latest reply on Sep 6, 2016 2:22 PM by Intel Corporation

    NUC6i3SYH (BIOS 0051) CIR wakeup not working, ever




      I tried every possible configuration, but I'm not able to wakeup my NUC6i3SYH with remotecontrol.

      I enabled CIR in BIOS ("Enhanced Consumer IR" in "Devices" tab and "Wake from S4 and S5 via CIR" in "Power" tab, S4/S5 deepsleep is disabled.


      In LibreELEC, everything looks good, shutdown via remotecontrol works.


      zbox:~ # dmesg|grep -i cir

      [    4.103451] ite_cir: Auto-detected model: ITE8713 CIR transceiver

      [    4.103454] ite_cir: Using model: ITE8713 CIR transceiver

      [    4.103456] ite_cir: TX-capable: 1

      [    4.103457] ite_cir: Sample period (ns): 8680

      [    4.103458] ite_cir: TX carrier frequency (Hz): 38000

      [    4.103460] ite_cir: TX duty cycle (%): 33

      [    4.103461] ite_cir: RX low carrier frequency (Hz): 0

      [    4.103462] ite_cir: RX high carrier frequency (Hz): 0

      [    4.127392] input: ITE8713 CIR transceiver as /devices/virtual/rc/rc0/input7

      [    4.127450] rc rc0: ITE8713 CIR transceiver as /devices/virtual/rc/rc0

      [    4.145175] ite_cir: driver has been successfully loaded

      [    4.157613] rc rc0: lirc_dev: driver ir-lirc-codec (ite-cir) registered at minor = 0


      zbox:~ # irw

      6c 0 KEY_DOWN devinput

      6c 0 KEY_DOWN_UP devinput

      67 0 KEY_UP devinput

      67 0 KEY_UP_UP devinput

      6a 0 KEY_RIGHT devinput

      6a 0 KEY_RIGHT_UP devinput

      69 0 KEY_LEFT devinput

      69 0 KEY_LEFT_UP devinput

      202 0 KEY_NUMERIC_2 devinput

      202 0 KEY_NUMERIC_2_UP devinput

      205 0 KEY_NUMERIC_5 devinput

      205 0 KEY_NUMERIC_5_UP devinput

      208 0 KEY_NUMERIC_8 devinput

      208 0 KEY_NUMERIC_8_UP devinput

      74 0 KEY_POWER devinput

      74 0 KEY_POWER_UP devinput




      the CIR seems to be connected to PCI0 (?):

      zbox:~ # cat /sys/bus/acpi/devices/ITE8713\:00/path





      but adding it to /proc/acpi/wakeup doesnt seem to do anything:

      zbox:~ # echo PCI0>/proc/acpi/wakeup


      zbox:~ # cat /proc/acpi/wakeup

      Device  S-state   Status   Sysfs node

      PEG0      S4    *disabled

      PEGP      S4    *disabled

      PEG1      S4    *disabled

      PEGP      S4    *disabled

      PEG2      S4    *disabled

      PEGP      S4    *disabled

      SIO1      S3    *disabled  pnp:00:00

      RP09      S4    *disabled

      PXSX      S4    *disabled

      RP10      S4    *disabled

      PXSX      S4    *disabled

      RP11      S4    *disabled

      PXSX      S4    *disabled

      RP12      S4    *disabled

      PXSX      S4    *disabled

      RP13      S4    *disabled

      PXSX      S4    *disabled

      RP01      S4    *disabled

      PXSX      S4    *disabled

      RP02      S4    *disabled

      PXSX      S4    *disabled

      RP03      S4    *disabled

      PXSX      S4    *disabled

      RP04      S4    *disabled

      PXSX      S4    *disabled

      RP05      S4    *disabled  pci:0000:00:1c.0

      PXSX      S4    *disabled  pci:0000:01:00.0

      RP06      S4    *disabled

      PXSX      S4    *disabled

      RP07      S4    *disabled

      PXSX      S4    *disabled

      RP08      S4    *disabled

      PXSX      S4    *disabled

      RP17      S4    *disabled

      PXSX      S4    *disabled

      RP18      S4    *disabled

      PXSX      S4    *disabled

      RP19      S4    *disabled

      PXSX      S4    *disabled

      RP20      S4    *disabled

      PXSX      S4    *disabled

      RP14      S4    *disabled

      PXSX      S4    *disabled

      RP15      S4    *disabled

      PXSX      S4    *disabled

      RP16      S4    *disabled

      PXSX      S4    *disabled

      GLAN      S4    *disabled  pci:0000:00:1f.6

      XHC       S4    *enabled   pci:0000:00:14.0

      XDCI      S4    *disabled

      HDAS      S4    *disabled  pci:0000:00:1f.3





      Is it possible that my hardware is broken?