Hi Folks, We are trying to bond two SRIOV VF's (coming out of two different PF's) within a Linux VM in active loadbalance mode using linux bonding driver. This is primarily to have high-availability across the...
Recently there were a few stories published, based on a blog post by an end-user, suggesting specific network packets may cause the Intel® 82574L Gigabit Ethernet Controller to become unresponsive until corrected ...
<><> Apologies if this has been posted in the wrong place <><> Ok I'll keep this brief. Problem:- LAN regulary disconnects and reconnets 30 seconds later. Symptons:- Lo...
We am looking for a quad port PCI express card with 100base-FX interfaces, under Windows 7 32-bit. Does the I340-F4 support 100base-FX SFP modules? I am not sure if SFP modules are plug-and-play for different speeds ...
etnerCan any of the following 3 NetEffect 10Gbe Ethernet Adapters that use PCIe v1.1 x8 lane be used on a Dell 2950 II that has PCIe v1.0 with an open x8 slot? I have not been able to find any other 10Gbe network adap...
Hello, I have a 82576 NIC for which I enabled SR-IOV support. All seems to work fine except I want to disable the anti-spoofing proctection (as described here [1]) and the command fails: # ip link set ...
I have a Dell Optiplex with an Intel 82567LM-3 Gigabit ethernet card and using unicast WOL. I have the most recent BIOS with deep sleep disabled and wake from off enabled. The problem is getting the computer to wake w...
We are configuring VFs for our high-volume network traffic, but want to continue to use Linux bridging for other VMs. Is there some configuration we need to do to enable packets from a VF to be switched to a bridge of...
Hello, Config-centric info: Using HP BL460C-G8 and 560FLB (82599 based) NIC. Host and guest OS is RHEL6.4 (latest - 2.6.32-358.2.1.el6.x86_64). Guest is defined SRIOV interfaces, but when booting, the b...
Hi, I have installed x520-SR2 on my Dell poweredge server running ESXi 5.1. I have configured this CNA with software FCoE The driver version on the CNA is ixgbe 3.14.3. How can I find the Firmware version on ...
Hi everybody, we are trying to set up FPP using Intel's 82599EB 10-Gbit/s Cards. Furthermore we are using the ixgbe driver version 3.14.5. I am loading the driver using modprobe ixgbe max_vfs=4,4,4,4 ...
I have a software application that runs on a laptop running Windows 7 SP1 which receives data at around 100Mbps via a UDP stream over a 1GbE connection. I've run the software on multiple laptops successfully in ...
Anyone know if this is possible? I'm trying to get Resonate to work with a new Intel NIC and Resonate's tech support thinks that this feature is why their product isn't working. I'm hoping to avoid going o...
Hello, I am looking for some tech background information about why its not possible to use a x520 card as virtual switch (creating VLAN is disabled as well) that is used for boot from iscsi in hyper-v. is this...
The Intel® Development Forum in Beijing took place two weeks ago and the interest in my two SDN-related presentations was very high. My poster chat drew about 40 or so people who stopped by in groups of 6-...
Hi, I've tried to connect my X520-DA2 to a Netgear GS752TXS using a 7m direct attach cable (Cisco SFP-H10GB-ACU7M) but I get no link. I've tried both NIC ports and all the SFP+ switch ports. What could be th...
“An inflection point is an event that changes the way we think and act.” With this quote from Andy Grove in her keynote speech, Rose Schooler, VP of Intel Architecture Group and GM of Intel's Commu...
I have a Dell 720 Server with a I350-T4 card installed with the latest drivers and firmware running Server 2012 with the HyperV role. I am having trouble creating a Virtual switch in HyperV that will show SR-IOV...
I have 3 PC's, each of which is running Windows 7 x64, and each of which had no prior problems connecting to the internet or the network via their PCI-e Intel Gigabit CT Desktop Adapters. Over the course of the ...
