Intel Communities: Message List - Problem of reboot of the computer after improvement of the processor with E4500 on Q8300

Re: Problem of reboot of the computer after improvement of the processor with E4500 on Q8300

i@isigns.co.za — Sat, 02 Apr 2011 07:44:28 GMT

Hi I got a D965xbx intel board and upgraded to Q8300 prossersor but know my computer do not start up and if I replace old prossers also it does n't

start! any idea?

Re: Problem of reboot of the computer after improvement of the processor with E4500 on Q8300

i@isigns.co.za — Sat, 02 Apr 2011 07:39:24 GMT

I had same problem with 3 long beeps when I upgraded mem to 8 gb - 4 x 2 gb

remove the graphics card then install mem and wait till computer starts up hold powerbutton in ,

replace graphics card and 3 beeps gone and mem installed.

mabe it will help for you also.

Re: Problem of reboot of the computer after improvement of the processor with E4500 on Q8300

webadmin@intel.com — Mon, 01 Mar 2010 13:21:52 GMT

The same result, boots at the first inclusion normally and when there is a reboot silence, but the fan on the processor turns on maximum turns

Re: Problem of reboot of the computer after improvement of the processor with E4500 on Q8300

webadmin@intel.com — Mon, 01 Mar 2010 13:18:58 GMT

Yes, three long beeps

Re: Problem of reboot of the computer after improvement of the processor with E4500 on Q8300

webadmin@intel.com — Mon, 01 Mar 2010 01:48:24 GMT

1. Restart the system into BIOS by pressing <F2> during the boot process.

2. Once in the BIOS setup utility, press <F9> to restore BIOS default settings.

3. Clear all DMI event logs by setting the option to "Enable", which is located in the Advanced/Event Log Configuration section of the BIOS Setup utility.

4. Press <F10> to save the new settings and reboot the system.

I saw another posting similar to this issue. It was related to the DG35EC board but I am not seeing it now. They had a similar issue. The person upgraded from Pentium Dual Core to a Core 2 Duo on a cold start it was fine - but upon a reboot it would not boot.

Re: Problem of reboot of the computer after improvement of the processor with E4500 on Q8300

webadmin@intel.com — Mon, 01 Mar 2010 01:21:16 GMT

may i ask ... .

when you power up the system with the ram removed.. is there any sound

Re: Problem of reboot of the computer after improvement of the processor with E4500 on Q8300

webadmin@intel.com — Sun, 28 Feb 2010 18:01:39 GMT

Thanks, but have helped nothing (. What do Next?

Re: Problem of reboot of the computer after improvement of the processor with E4500 on Q8300

webadmin@intel.com — Sun, 28 Feb 2010 16:37:38 GMT

plug out all other connecting device such as HDD and cd rom..

then power the system up... if you see post and display on the monitor.. you are lucky... off the system and plug back.. power up the system once all cable and power cable are securely connected..

if the board still fail to boot.. pls take out the ram.. and on the mainboard with the processor connected... is there any sound... if they is sound.. pls resit your ram modules and try booting..

if all cannot work... pls take out your CMOS battery and leave it without any power source for more than 15 mintues.. maybe you shall go and have a hot coffee watching tv..

after the 15 min break.. place the battery back and power the system...

Problem of reboot of the computer after improvement of the processor with E4500 on Q8300

webadmin@intel.com — Sun, 28 Feb 2010 15:49:48 GMT

Hi all,

Motherboard: DG33TL
BIOS: DPP3510J.86A.0572.2009.0715.2346 the last
HDD: 2x80GB SATA
The RAM: 4x1 Gb
The processor: Q8300

The computer switches on normally. After reboot the computer does not boot. What to do?

Thanks all.